 《分享》Windows 2003 with Raid Card driver install |       |
Windows 2003以現今角度來說，算是一個比較舊的作業系統，
一些新的Server、IPC在安裝Windows 2003時，遇到最大的問題就是如何在安裝時載入Raid Card的驅動程式，
讓作業系統能夠順利安裝。
若主機板上有onboard floppy介面，把Raid Card廠商提供的驅動程式放入floppy後，
透過Windows 2003安裝時，按下F6按鈕及S鍵來載入Raid Card驅動程式，
算是一個最傳統也最OK的方式。
萬一沒有onboard floppy介面時，透過USB floppy來載入驅動程式，
常常會發現第一階段按下S鍵入驅動程式時，
明明還抓的到Raid Card驅動程式，可成功識別到HD。
但真正要安裝Windows 2003檔案時，卻又抓不到USB floppy而無法安裝下去...
參考以下兩個連接後，發現是在driver裏txtsetup.oem無法識別外接USB裝置。
http://support.microsoft.com/kb/916196
http://www.msfn.org/board/topic/82711-us...ith-usb-floppy/
解決方法是在txtsetup.oem裏HardwareIds區段加入以下USB裝置的描述 #--The following lines give additional USB floppy support
id = "USB\VID_03F0&PID_2001", "usbstor" #--HP
id = "USB\VID_054C&PID_002C", "usbstor" #--Sony
id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data
id = "USB\VID_0409&PID_0040", "usbstor" #--NEC
id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC
id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega
id = "USB\VID_055D&PID_2020", "usbstor" #--Samsung
以下以LSI SAS Raid card driver的txtsetup.oem為例[Disks]
megasas2 = "LSI MegaRAID SAS RAID Controller Driver", \megasas2.sys, \
[Defaults]
scsi = megasas2
[scsi]
megasas2 = "LSI MegaRAID SAS RAID Controller Driver", megasas2
[HardwareIds.scsi.megasas2]
megasas2 = "PCI\VEN_1028&DEV_0015", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_005B", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_005D", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_005F", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0060", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0071", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0073", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0078", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0079", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0409", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0411", "megasas2"
megasas2 = "PCI\VEN_1000&DEV_0413", "megasas2"
#--The following lines give additional USB floppy support
id = "USB\VID_03F0&PID_2001", "usbstor" #--HP
id = "USB\VID_054C&PID_002C", "usbstor" #--Sony
id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data
id = "USB\VID_0409&PID_0040", "usbstor" #--NEC
id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC
id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega
id = "USB\VID_055D&PID_2020", "usbstor" #--Samsung
[Files.scsi.megasas2]
driver = megasas2, megasas2.sys, megasas2
inf = megasas2, megasas2.inf, megasas2
catalog = megasas2, megasas2.cat
[Config.megasas2]
value = "", Tag, REG_DWORD, 20
不過這個部分順子沒有實機可以測試，所以目前無法驗證其可行性，
但以討論串的後來的回覆內容來看，應該是可行無誤的。
 |
 |
♥順子老婆的網拍，請多關照∼
If you don't like something, change it.
If you can't change it, change your attitude.
Don't complain!
|
2013-07-23, 13:38
測試結果出爐